Cooper Security M2000 Specifikace stáhnout pdf (Strana 8)

8 M2000 Installation Instructions

CIRCUIT 2

Z2 T2

2K2

4K7

Tamper

Ala rm

Sh o rt C i r c u it Tamper Alarm

Open Circuit Tamper Alarm

Zo n e

Re si st a n c e

He a lt hy

Masked

Ala rm

9.1k

2.2k

4.4k

6.9k

Ant i-m a sk

Figure 6: Anti-Masking Zone Wiring

Network Connections

Network 1 and 2 Connections

("2" and "3" in Figure 2.)

Control Panel Network

Spare core used to double

up "B" to reduce voltage

6 Core

Alarm Cable

Po we r fo r

detectors

Po we r fo r

detectors

Po we r fo r

detectors

Po we r fo r

detectors

I/D= 2

I/D= 1

I/D= 3

I/D= 4

Re m o t e

Ke y p a d

Re m o t e

Ke y p a d

Re m o t e

Ke y p a d

Re m o t e

Ke y p a d

ABCDE

metres (

ax.)

Figure 7: Keypad Connections

Networks 1 and 2 can connect to one of the following

(see Figure 3):

• A combination of up to five keypads and/or LEC2s.

Wiring is the same as in Figure 7.

• A maximum of 16 MSNodes, MSPSUs, or

MRNodes. Please refer to the Installation

Instructions for each device for connection details.

Note: Do not connect MSNodes, MSPSUs or

MRNodes directly to the same network as a keypad,

LEC2 or ID Node/MIDNode.

Telephone Connections

("4" and "5" in Figure 2.)

An M2000 contains a built-in modem. This enables

direct connection to a PSTN telephone network or

PABX exchange.

This allows the system to be controlled and monitored

from a remote PC running the Downloader software,

and enables alarm status information to be

transmitted to an Alarm Receiving Centre.

You can connect the control panel to a telephone

network using either of the following:

• The RJ11 telecom socket (labelled "5" in Figure 2).

Use only a pre-manufactured and approved cable

between the RJ11 socket and telephone outlet

socket.

• The PSTN terminal block (labelled "4" in Figure 2).

Connection details are shown in Figure 8.

Do not

make any other connections to the telephone

network.

Optional connec tion to only one other item

of equipment (e.g. fax or answer machine).

While the control panel is communicating,

any device connected to the "Diverted Line"

is auto m a tic ally d isc o nne c te d .

En su re p o l a ri t y

is c orrec t.

Use cable type

1/05m m CW1308

BT Ma st e r Box

(Exc lusive line )

Control Panel

Do not connect

Diverte d

Li n e

Pr i m a r y

Li n e

2 or B

5 or A

Figure 8: PSTN Connections

The control panel is not suitable for connection as an

extension to a payphone or to "1+1" carrier systems.

If required, you can fit an ADSL line filter to the

connector immediately behind the PSTN terminal

block. Cooper Security Ltd supply part number ADSL01

for this purpose. Before fitting the filter remove the

jumpers from the connector as shown in Figure 9

below.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Komentáře k této Příručce

Žádné komentáře

Cooper Security M2000 Specifikace Strana 8

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Cooper Security M2000