Cooper Security M2000 Specifikace stáhnout pdf (Strana 14)

14 M2000 Installation Instructions

A serial or USB port cannot be used to connect a

printer.

(Female 9-pin)

Ne two rker II

(Female 9-pin)

Figure 21: RS232 Connections to a PC

Power Availability

Before connecting any external devices to the control

panel, you must make sure that the control panel can

provide sufficient current to power them.

The amount of current available from the panel

depends on the standard and grade in use, the battery

fitted, and (for Grade 3 only) whether AC Fails are

transmitted to an ARC. See Table 2 or3.

Using 4, calculate the total current taken by all devices

used (except the battery), and make sure that this does

not exceed the available current.

If the total current required exceeds the amount

available, add more power supplies.

Fitted Battery Size Available Current Grade 1 or 2

7Ah 580mA

17Ah 750mA

Table 2: Available Current - Grade 1 or 2, PD6662 or EN50131-1

Table 3: Available Current - Grade 3, PD6662 or EN50131-1

Device Current

Control panel PCB 200mA

Extension loudspeaker ("13" in Figure 2), if used 100mA

Bell ("9" in Figure 2) Device

dependent

Devices powered from digital communicator

and transistor outputs ("8" and "6" in Figure 2)

Device

dependent

Each PIR or other device powered from the

12Vdc output ("16" in Figure 2)

Device

dependent

Each keypad:

MKP1

MKP2

90mA

80mA

Each ID Node/MIDNode

Each MSNode (non-alarm state excl. speaker)

Each MSNode (alarm state incl. spkr, max.)

Each MRNode

Each output module

Each LEC2

160mA(max)

60mA

310mA

55mA

5mA

40mA

Table 4: Current Consumption Figures

Connecting to the Mains Supply

WARNING: ENSURE THAT THE MAIN SUPPLY IS

DISCONNECTED AND ISOLATED BEFORE MAKING

ANY MAINS CONNECTIONS.

All mains electrical connections must be carried out by

a qualified electrician and must comply with the

current local regulations (e.g. IEE). The supply must be

fed from an un-switched fused spur fitted with a 3A

fuse.

The unit shall be installed incorporating a disconnect

device which has a 3mm air contact separation in all

poles.

The mains supply is connected to a 3-way "Euro Type"

fused terminal block (see Figure 22). Ensure that the

earth wire is longer than the live and neutral to ensure

that the earth is the last to take any strain.

To Control Panel

Transformer

315mA

N(L)P

230Vac

Figure 22: Mains Connections

Note: To avoid mains interference, the mains cable

must enter the control panel through its own cable

entry hole (see Figure 1) and must not be mixed with

other cables.

The mains cable must be anchored down with a strain-

relief tie. There is a eye located to the top-left of the

mains cable entry hole for this purpose.

Available Current Grade 3

AC Fail to ARC No AC Fail to ARC

Fitted

Battery

Size

PD6662

Grade 3

EN50131-1

Grade 3

PD6662

Grade 3

EN50131-1

Grade 3

7Ah 580mA 230mA 290mA Not valid

17Ah

750mA

560mA

700mA

280mA

1 2 ... 9 10 11 12 13 14 15 16

Komentáře k této Příručce

Žádné komentáře

Cooper Security M2000 Specifikace Strana 14

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Cooper Security M2000