Cooper Security 9751 Instalační příručka Strana 7
- Strana / 96
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
496792 1
1. Introduction
1. INTRODUCTION
The 9751 and 9752 control units are designed to be fully programmable to
suit individual site requirements and user needs.
The system comprises a control unit in a shielded case, up to four separate
keypads and one keyswitch interface (see Figure 1 on the next page). You
should always fit at least one keypad.
The control unit provides:
° A four-wire bus connection for keypads, keyswitches and hardwired or
wireless zone expanders.
° Connections for eight Fully Supervised Loop (FSL) zones or eight
closed circuit zones with a common tamper.
° Connections for three fully programmable outputs.
° Internal sounder loudspeaker output with electronically generated
Chime, Alarm, Fire and Entry/Exit tones. (The volume of the Entry/Exit
and Chime tones can be adjusted).
° Built in communicator for reporting to an Alarm Receiving Centre
(ARC).
° Pins for fitting a plug-by communication device.
° Remote up/downloading. (A local socket is available on the 9752.)
The control unit provides connectors for eight Closed Circuit (CC) zones or
eight Fully Supervised Loop (FSL) zones on its own printed circuit board.
Separate 9954 expander units allow connection of a further 16 wired zones to
a 9751 or 24 wired zones to a 9752. Alternatively, a 9955 expander allows
connection of 16 wirefree zones to a 9751 or 24 to a 9752. Both control units
can use a combination of wired and wireless expanders.
The control units support the 9930 sixteen character Liquid Crystal Display
(LCD) keypad. In addition the control units also supports the 9928 keyswitch
interface.
As an Installer you can program the system either from the keypads, or
using PC based Windows <Downloader>. When programming from the
keypads the programming interface is arranged as a set of three-digit num-
bered commands similar to those used by the 9800 family of products.
The system can provide for up to 16 separate users. User facilities include:
° Three different security levels (full set and two part sets) on the 9751
or four levels on the 9752. The levels can be programmed by the
Installer.
° User programmable Duress code.
° Keyswitch setting/unsetting.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Cooper Security 9751
(16 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce