Cooper Security M2000 Uživatelská příručka

MENVIERSECURITY M2000/M800 USER'S GUIDE HARDWIRED CONTROL PANELS

8 Setting Additional Wards If the system already has one ward set and you want to set another ward: BANNER TEXT 17:30 Sun 01 JAN 1. At the keypad,

9 Setting Ward Groups BANNER TEXT 17:30 Sun 01 JAN 1. At the keypad, enter your user code or present your proximity tag. Set Ward? Ward > **...

10 Unsetting Your Alarm System To unset the alarm system, go directly to the keypad and follow the instructions in one of the two sections dependin

11 If there is no sound (you have not started the entry timer): 1. Enter your user code or present your proximity tag to the keypad. ENT=Unset Syst

12 Unset Group 1? To Unset a Ward Group Press 9. Press ¬ or | to select the Group you want. Unset Group 2? The display shows the Group you have

13 Silencing an Alarm If an alarm has occurred and you want to silence the sounders: 1. Enter your user code or present your proximity tag. This si

14 Resetting the System Resetting the system lets you review the alerts that have taken place and clear the ALERTS message from the main display. I

15 Press ENT To Reset 4. You will see the message shown opposite once you have reviewed each message. Press [ to reset the system. The ALERT

16 The ARC will ask you for details of the alarm. If there is no need for an engineer to visit, the ARC will give you a remote reset code. 4.

17 Using a Telecommand A telecommand is a small remote control that you can attach to a keyring. The telecommand has four buttons and a small light t

Contents Introduction ... 1 About the Alarm System ...

18 Setting Make sure the system is idle. Secure all your windows and doors. 1. Press the appropriate button on the telecommand. The internal sound

19 Troubleshooting Setting the System with Zones Active Overview If you try to set the system with one or more zones active, the control unit will: E

20 “Dee Dah Dee Dah...” Office window 2002 Active Office door 2001 Active 1. The system gives a high, rapid, repeating tone and the display shows

21 Alert Messages This section gives the meaning of the messages that you might see when resetting the system (page 14). Contact your alarm company i

22 BELL TAMPER 12:00 Sun 01 JAN The lid of the external sounder has been removed. You may not be able to set your system until the fault is cleared.

23 Other Messages SERVICE REQUIRED 12:00 Sun 01 JAN The alarm system needs a routine maintenance visit. You can still set and unset the system but yo

24 Sorry,cannot set Aux X tamp open Cannot set because of a tamper fault on auxiliary zone 1. Contact the alarm company. Sorry,cannot set Bell box ta

25 Notes

26 © Cooper Security Limited 2010 Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor C

1 Introduction This guide describes how to set and unset your intruder alarm system. It also describes how to silence the sounders in the event of an

2 User Codes and Proximity Tags To operate the system you must have a numeric “user code” or a plastic “proximity tag”. A user code is a unique 4 or

3 Keypad Features 1. Display: Normally shows the date, time and a banner message (chosen by your alarm company1). When you operate the system, the di

4 Zones The alarm system has a number of “zones”. Each zone has a sensor, such as a movement detector or door contact, that is monitored by the alarm

5 Operating your Alarm System Setting Your Alarm System To set the system or a ward carry out the following steps: 1. Identify yourself at the keypa

6 To Choose All Wards (Full Set1): If you want to set all your wards, press [ and leave the premises (see the next page). To Choose One Ward

7 Exit Now Arming System 3. Leave the Premises and Complete Setting Leave by the designated exit route. The internal sounder gives a tone to